29 CFR 1910 · General Industry · Subpart O

1910.213(c)(3): Nonkickback Fingers on Hand-Fed Ripsaws

By Black Belt Safety Editorial Team Official text as of October 15, 2026 Data updated November 17, 2026 3 min read

In plain words:

Employers must equip each hand-fed circular ripsaw with nonkickback fingers or dogs placed to oppose the saw's tendency to pick up the material or throw it back toward the operator. They must hold well enough for all thicknesses of material being cut.

Key takeaways

  • 1910.213(c)(3) is part of OSHA's general industry standards (29 CFR Part 1910, Subpart O).
  • OSHA cited it 252 times in the last 3 years, in 252 inspections, with $291,042 in current penalties.
  • 1 death is linked to inspections that cited this rule.
  • Most citations: MN (45), CT (21), NC (20).
  • Related part: 1910.213(c) Hand-fed ripsaws (803 citations).
  • Free 5-minute toolbox talk for your crew below.

Get the free 5-minute toolbox talk on 1910.213(c)(3) ↓

252citations, 3 years
$291,042current penalties
252inspections
1linked deaths
In this article
  1. What this rule covers
  2. Official text
  3. Injuries linked to this rule
  4. Where and how often it was cited
  5. Free toolbox talk
  6. OSHA interpretation letters
  7. Related parts of this rule
  8. Get your crew competent
  9. Frequently asked questions
  10. About this page

What this rule covers

29 CFR 1910.213(c)(3) is one requirement inside 1910.213 Woodworking machinery requirements, an OSHA general industry standard (Part 1910, Subpart O). The official text below is copied word for word from the Electronic Code of Federal Regulations (eCFR). The numbers, injury cases and training on this page show how OSHA enforces it on real job sites.

Official text

(3) Each hand-fed circular ripsaw shall be provided with nonkickback fingers or dogs so located as to oppose the thrust or tendency of the saw to pick up the material or to throw it back toward the operator. They shall be designed to provide adequate holding power for all the thicknesses of materials being cut. 252 citations

Source: eCFR, text current as of 2026-10-15. Read all of 1910.213.

See every company cited for this rule.

Export the list: 252 inspections cited 1910.213(c)(3) in the last 3 years, with employer, location, penalty and date.

Purple Belt, $59/mo

Injuries linked to this rule

1 death is linked to inspections where OSHA cited 1910.213(c)(3).

Employee is killed when head is crushed by stacker carriage
2023-12-05 · Fatal · APPLETON, WI

At 3:45 a.m. on December 5, 2023, three employees were operating a resaw stacker. Coworker #1 was operating the infeed side, while Coworker #2 trained Employee #1 on operating the stacker side. The resaw stacker takes pre-cut boards and rips them down to smaller sizes…

Where and how often it was cited

YearCitations
20236
2024115
202575
202656

Top states: MN (45), CT (21), NC (20), FL (15), UT (15)

Largest penalties

EmployerLocationPenalty for this rule
LOUDOUN STAIRS INC.PURCELLVILLE, VA$158,725
FIXTURE CONCEPTS INCSAINT PETERS, MO$9,268
MANUFACTURED HOUSING ENTERPRISES, INC.BRYAN, OH$7,022
ELITE BOOTH LLCRAYTOWN, MO$6,951
BOWTIE HOSPITALITY LV LLCLAS VEGAS, NV$6,832

Free toolbox talk

A 5-minute crew talk on 1910.213(c)(3), plus alerts when this rule changes. Free.




OSHA interpretation letters

None exist. OSHA has not published a letter of interpretation for 1910.213(c)(3).

Related parts of this rule

Get your crew competent

Trainers on Black Belt Safety: Marc Harvey

Trainers and suppliers: feature your business on this rule for $25/month.

Frequently asked questions

What must a hand-fed circular ripsaw have?

Nonkickback fingers or dogs.

What do the nonkickback fingers do?

They oppose the thrust or tendency of the saw to pick up the material or throw it back toward the operator.

Do they need to work for thick and thin material?

Yes. They must provide adequate holding power for all the thicknesses of materials being cut.

About this page

Sources

3-year window. Federal OSHA only; state-plan rules are not counted. Plain-language text is a summary, not legal advice; the official text controls. Black Belt Safety is not part of OSHA or the Department of Labor.

Written and reviewed by

Black Belt Safety Editorial Team

Site Safety Officer and Safety Professional

OSHA 30 · CPR · USACE CQM

Written and reviewed by the Black Belt Safety team. Every post is checked against the OSHA standard or agency source it cites.

Scroll to top