29 CFR 1910 · General Industry · Subpart O

1910.219(c)(2): Guarding Horizontal Shafting

By Black Belt Safety Editorial Team Official text as of October 15, 2026 Data updated November 17, 2026 3 min read

In plain words:

All exposed horizontal shafting seven feet or less from the floor or work platform must be enclosed by a stationary casing or a trough, except runways used only for oiling or running adjustments. Shafting under bench machines must be enclosed by casing or trough, with trough sides within six inches of the table underside or floor and extending at least two inches beyond the shafting.

Key takeaways

  • 1910.219(c)(2) is part of OSHA's general industry standards (29 CFR Part 1910, Subpart O).
  • OSHA cited it 321 times in the last 3 years, in 319 inspections, with $1,231,827 in current penalties.
  • 5 deaths are linked to inspections that cited this rule.
  • Most citations: IA (34), NC (31), VA (23).
  • Related part: 1910.219(c) Shafting (707 citations).
  • Free 5-minute toolbox talk for your crew below.

Get the free 5-minute toolbox talk on 1910.219(c)(2) ↓

321citations, 3 years
$1,231,827current penalties
319inspections
5linked deaths
In this article
  1. What this rule covers
  2. Official text
  3. Injuries linked to this rule
  4. Where and how often it was cited
  5. Free toolbox talk
  6. OSHA interpretation letters
  7. Related parts of this rule
  8. Get your crew competent
  9. Frequently asked questions
  10. About this page

What this rule covers

29 CFR 1910.219(c)(2) ("Guarding horizontal shafting") is one requirement inside 1910.219 Mechanical power-transmission apparatus, an OSHA general industry standard (Part 1910, Subpart O). It includes 2 sub-paragraphs. The official text below is copied word for word from the Electronic Code of Federal Regulations (eCFR). The numbers, injury cases and training on this page show how OSHA enforces it on real job sites.

Official text

(2) Guarding horizontal shafting. 321 citations

(i) All exposed parts of horizontal shafting seven (7) feet or less from floor or working platform, excepting runways used exclusively for oiling, or running adjustments, shall be protected by a stationary casing enclosing shafting completely or by a trough enclosing sides and top or sides and bottom of shafting as location requires. Open (c)(2)(i) 308 citations

(ii) Shafting under bench machines shall be enclosed by a stationary casing, or by a trough at sides and top or sides and bottom, as location requires. The sides of the trough shall come within at least six (6) inches of the underside of table, or if shafting is located near floor within six (6) inches of floor. In every case the sides of trough shall extend at least two (2) inches beyond the shafting or protuberance. 3 citations

Source: eCFR, text current as of 2026-10-15. Read all of 1910.219.

See every company cited for this rule.

Export the list: 319 inspections cited 1910.219(c)(2) in the last 3 years, with employer, location, penalty and date.

Purple Belt, $59/mo

Injuries linked to this rule

5 deaths are linked to inspections where OSHA cited 1910.219(c)(2).

Employee is struck by robotic arm while cleaning sensor and
2024-12-02 · Fatal · SAINT AUGUSTINE, FL

At 10:35 a.m. on December 2, 2024, Employee #1 was performing maintenance on a sensor inside a robotic enclosure. As he entered the area, the robot was stoppedby entrance sensors. While he was cleaning the sensor, a coworker reset the machine from the control panel,…

See all 5 cases

Full case list with employer, penalty, filters and download is part of OSHA Data (Purple Belt).

Unlock with Purple Belt

Where and how often it was cited

YearCitations
202311
2024124
2025112
202674

Top states: IA (34), NC (31), VA (23), WI (20), MN (17)

Largest penalties

EmployerLocationPenalty for this rule
GREAT KITCHENS FOOD COMPANY, INC.BROCKTON, MA$40,000
68657 - DURO HILEX POLY LLCFLORENCE, KY$28,000
COMMONWEALTH OF VIRGINIA DEPARTMENT OF TRANSPORTATIONNORFOLK, VA$16,285
THE GOODYEAR TIRE & RUBBER COMPANYDANVILLE, VA$15,875
GREAT DANE LLCWAYNE, NE$15,625

Free toolbox talk

A 5-minute crew talk on 1910.219(c)(2), plus alerts when this rule changes. Free.




OSHA interpretation letters

None exist. OSHA has not published a letter of interpretation for 1910.219(c)(2).

Related parts of this rule

Get your crew competent

Trainers on Black Belt Safety: Marc Harvey

Trainers and suppliers: feature your business on this rule for $25/month.

Frequently asked questions

When must horizontal shafting be guarded?

When exposed parts are seven (7) feet or less from the floor or working platform.

What guard types are allowed?

A stationary casing enclosing the shafting completely, or a trough enclosing sides and top or sides and bottom.

How far must trough sides extend?

At least two (2) inches beyond the shafting or protuberance.

About this page

Sources

3-year window. Federal OSHA only; state-plan rules are not counted. Plain-language text is a summary, not legal advice; the official text controls. Black Belt Safety is not part of OSHA or the Department of Labor.

Written and reviewed by

Black Belt Safety Editorial Team

Site Safety Officer and Safety Professional

OSHA 30 · CPR · USACE CQM

Written and reviewed by the Black Belt Safety team. Every post is checked against the OSHA standard or agency source it cites.

Scroll to top