29 CFR 1910 · General Industry · Subpart R

1910.262(c): Textile Machine Safety Requirements

By Black Belt Safety Editorial Team Official text as of October 15, 2026 Data updated November 17, 2026 4 min read

In plain words:

Every textile machine must have its own mechanical or electrical means of stopping, with locking-type shifters on belt-driven machines and protection against automatic restart after power failure where injury could result. Handles must be long enough to keep hands off moving parts, guards and safety devices must be maintained, and lighting, piping identification and exposed steam pipes within seven feet of the floor must meet the listed requirements.

Key takeaways

  • 1910.262(c) is part of OSHA's general industry standards (29 CFR Part 1910, Subpart R).
  • OSHA cited it 4 times in the last 3 years, in 4 inspections, with $24,648 in current penalties.
  • 1 death is linked to inspections that cited this rule.
  • Related part: 1910.262(c)(5) Inspection and maintenance (3 citations).
  • Free 5-minute toolbox talk for your crew below.

Get the free 5-minute toolbox talk on 1910.262(c) ↓

4citations, 3 years
$24,648current penalties
4inspections
1linked deaths
In this article
  1. What this rule covers
  2. Official text
  3. Injuries linked to this rule
  4. Where and how often it was cited
  5. Free toolbox talk
  6. OSHA interpretation letters
  7. Related parts of this rule
  8. Get your crew competent
  9. Frequently asked questions
  10. About this page

What this rule covers

29 CFR 1910.262(c) ("General safety requirements") is one requirement inside 1910.262 Textiles, an OSHA general industry standard (Part 1910, Subpart R). It includes 8 sub-paragraphs. The official text below is copied word for word from the Electronic Code of Federal Regulations (eCFR). The numbers, injury cases and training on this page show how OSHA enforces it on real job sites.

Official text

(c) General safety requirements — 4 citations

(1) Means of stopping machines. Every textile machine shall be provided with individual mechanical or electrical means for stopping such machines. On machines driven by belts and shafting, a locking-type shifter or an equivalent positive device shall be used. On operations where injury to the operator might result if motors were to restart after power failures, provision shall be made to prevent machines from automatically restarting upon restoration of power.

(2) Handles. Stopping and starting handles shall be designed to the proper length to prevent the worker's hand or fingers from striking against any revolving part, gear guard, or any other part of the machine.

(3)-(4) [Reserved]

(5) Inspection and maintenance. All guards and other safety devices, including starting and stopping devices, shall be properly maintained. Open (c)(5) 3 citations

(6) Lighting. Lighting shall conform to American National Standard A11.1—1965, which is incorporated by reference as specified in § 1910.6.

(7) Identification of piping systems. Identification of piping systems shall conform to American National Standard A13.1—1956, which is incorporated by reference as specified in § 1910.6.

(8) Identification of physical hazards. Identification of physical hazards shall be in accordance with the requirements of § 1910.144.

(9) Steam pipes. All pipes carrying steam or hot water for process or servicing machinery, when exposed to contact and located within seven feet of the floor or working platform shall be covered with a heat-insulating material, or otherwise properly guarded. Open (c)(9) 1 citations

Source: eCFR, text current as of 2026-10-15. Read all of 1910.262.

See every company cited for this rule.

Export the list: 4 inspections cited 1910.262(c) in the last 3 years, with employer, location, penalty and date.

Purple Belt, $59/mo

Injuries linked to this rule

1 death is linked to inspections where OSHA cited 1910.262(c).

Employee dies of multiple trauma when pulled into carding ma
2024-11-01 · Fatal · FORT WORTH, TX

At 10:00 a.m. on November 1, 2024, an employee working for a staffing agency wascleaning around the equipment at a client site using compressed air. The employee crawled under a carding machine when the hood of his shirt was pulled into the rotating parts. The…

Where and how often it was cited

Free toolbox talk

A 5-minute crew talk on 1910.262(c), plus alerts when this rule changes. Free.




OSHA interpretation letters

None exist. OSHA has not published a letter of interpretation for 1910.262(c).

Related parts of this rule

Get your crew competent

Trainers on Black Belt Safety: Marc Harvey

Trainers and suppliers: feature your business on this rule for $25/month.

Frequently asked questions

What stopping means must textile machines have?

Individual mechanical or electrical means for stopping each machine.

What about restarts after a power failure?

Where injury might result, the machine must be prevented from automatically restarting when power returns.

How must exposed steam pipes be handled?

Pipes carrying steam or hot water within seven feet of the floor or platform must be insulated or otherwise guarded.

About this page

Sources

3-year window. Federal OSHA only; state-plan rules are not counted. Plain-language text is a summary, not legal advice; the official text controls. Black Belt Safety is not part of OSHA or the Department of Labor.

Written and reviewed by

Black Belt Safety Editorial Team

Site Safety Officer and Safety Professional

OSHA 30 · CPR · USACE CQM

Written and reviewed by the Black Belt Safety team. Every post is checked against the OSHA standard or agency source it cites.

Scroll to top