1926.1430: Crane and Derrick Training
Employers must train employees working with cranes and derricks, including those working near overhead power lines, signal persons, operators, competent and qualified persons, and everyone who works with the equipment on crush and pinch points. Operator training includes safe operation of their equipment, testing the boom hoist brake on friction equipment, and the manufacturer's emergency procedures where available.
Key takeaways
- 1926.1430 is part of OSHA's construction standards (29 CFR Part 1926, Subpart CC).
- OSHA cited it 18 times in the last 3 years, in 18 inspections, with $33,490 in current penalties.
- 2 deaths are linked to inspections that cited this rule.
- Most citations: MD (8), AK (3), IN (2).
- Most-cited part: 1926.1430(b) Signal persons (11 citations).
- Free 5-minute toolbox talk for your crew below.
Get the free 5-minute toolbox talk on 1926.1430 ↓
In this article
What this rule covers
29 CFR 1926.1430, "Training", is an OSHA construction standard (Part 1926, Subpart CC). It has 15 numbered paragraphs. The official text below is copied word for word from the Electronic Code of Federal Regulations (eCFR). The numbers, injury cases and training on this page show how OSHA enforces it on real job sites.
Official text
Show the full text of 1926.1430 (15 paragraphs)
The employer must provide training as follows:
(a) Overhead powerlines. The employer must train each employee specified in § 1926.1408(g) and § 1926.1410(m) in the topics listed in § 1926.1408(g).
(b) Signal persons. The employer must train each employee who will be assigned to work as a signal persons who does not meet the requirements of § 1926.1428(c) in the areas addressed in that paragraph. Open (b) 11 citations
(c) Operators.
(1) The employer must train each operator in accordance with § 1926.1427(a) and (b), on the safe operation of the equipment the operator will be using.
(2) The employer must train each operator covered under the exception of § 1926.1427(a)(2) on the safe operation of the equipment the operator will be using.
(3) The employer must train each operator of the equipment covered by this subpart in the following practices:
(i) On friction equipment, whenever moving a boom off a support, first raise the boom a short distance (sufficient to take the load of the boom) to determine if the boom hoist brake needs to be adjusted. On other types of equipment with a boom, the same practice is applicable, except that typically there is no means of adjusting the brake; if the brake does not hold, a repair is necessary. See § 1926.1417(f) and (j) for additional requirements.
(ii) Where available, the manufacturer's emergency procedures for halting unintended equipment movement.
(d) Competent persons and qualified persons. The employer must train each competent person and each qualified person regarding the requirements of this subpart applicable to their respective roles. 4 citations
(e) Crush/pinch points. The employer must train each employee who works with the equipment to keep clear of holes, and crush/pinch points and the hazards addressed in § 1926.1424 (Work area control). Open (e) 2 citations
(f) Tag-out. The employer must train each operator and each additional employee authorized to start/energize equipment or operate equipment controls (such as maintenance and repair employees), in the tag-out and start-up procedures in §§ 1926.1417(f) and (g).
(g) Training administration. Open (g) 1 citations
(1) The employer must evaluate each employee required to be trained under this subpart to confirm that the employee understands the information provided in the training. Open (g)(1) 1 citations
(2) The employer must provide refresher training in relevant topics for each employee when, based on the conduct of the employee or an evaluation of the employee's knowledge, there is an indication that retraining is necessary.
(3) Whenever training is required under subpart CC, the employer must provide the training at no cost to the employee.
[75 FR 48135, Aug. 9, 2010, as amended at 83 FR 56247, Nov. 9, 2018]
Source: eCFR, text current as of 2026-10-15.
Export the list: 18 inspections cited 1926.1430 in the last 3 years, with employer, location, penalty and date.
Purple Belt, $59/moInjuries linked to this rule
2 deaths are linked to inspections where OSHA cited 1926.1430.
At 10:30 a.m. on June 21, 2024, an employee working for an electrical contractorwas helping direct a boom crane. It is believed that one of the riggers failed causing the vehicle to become high center and overturn on the passenger side. The employee was struck…
Full case list with employer, penalty, filters and download is part of OSHA Data (Purple Belt).
Unlock with Purple BeltWhere and how often it was cited
| Year | Citations |
|---|---|
| 2024 | 4 |
| 2025 | 8 |
| 2026 | 6 |
Top states: MD (8), AK (3), IN (2), RI (2), OH (1)
Largest penalties
| Employer | Location | Penalty for this rule |
|---|---|---|
| HILCORP ALASKA, LLC | PRUDHOE BAY, AK | $11,292 |
| CHOSEN CONSTRUCTION, INC | PRUDHOE BAY, AK | $7,904 |
| PHILLIPS SOUTHERN ELECTRICAL COMPANY INC | FORT SCOTT, KS | $7,904 |
| JM QUALITY CONSTRUCTION LLC | FREMONT, OH | $3,042 |
| MUCK CONSTRUCTION | MUNCIE, IN | $1,400 |
Free toolbox talk
A 5-minute crew talk on 1926.1430, plus alerts when this rule changes. Free.
OSHA interpretation letters
None exist. OSHA has not published a letter of interpretation for 1926.1430.
Most-cited parts of this rule
- 1926.1430(b) Signal persons 11 citations
- 1926.1430(e) Crush/pinch points 2 citations
- 1926.1430(g) Training administration 1 citations
- 1926.1430(g)(1) 1 citations
Get your crew competent
Trainers on Black Belt Safety: Marc Harvey
Trainers and suppliers: feature your business on this rule for $25/month.
Frequently asked questions
Who must be trained under 1926.1430?
Employees covered by the power line rules, signal persons, operators, competent and qualified persons, and employees who work with the equipment.
What should operators do before moving a boom off a support on friction equipment?
First raise the boom a short distance to see if the boom hoist brake needs to be adjusted.
What crush and pinch point training is required?
Employees who work with the equipment must be trained to keep clear of holes, crush/pinch points and the hazards addressed in work area control.
About this page
Sources
- 29 CFR 1926.1430 (eCFR), text current as of 2026-10-15
- U.S. Department of Labor enforcement data: OSHA inspections, citations and accident records, copied nightly; data as of 2026-11-17
3-year window. Federal OSHA only; state-plan rules are not counted. Plain-language text is a summary, not legal advice; the official text controls. Black Belt Safety is not part of OSHA or the Department of Labor.
