29 CFR 1910 · General Industry · Subpart S

1910.335(a)(2)(i): Insulated Tools Near Energized Parts

By Black Belt Safety Editorial Team Official text as of October 15, 2026 Data updated November 17, 2026 3 min read

In plain words:

When working near exposed energized conductors or parts, each employee must use insulated tools or handling equipment if they might touch those parts, and protect the insulation if it can be damaged. Fuses with energized terminals must be removed or installed with fuse handling equipment insulated for the circuit voltage, and ropes and handlines near energized parts must be nonconductive.

Key takeaways

  • 1910.335(a)(2)(i) is part of OSHA's general industry standards (29 CFR Part 1910, Subpart S).
  • OSHA cited it 48 times in the last 3 years, in 48 inspections, with $248,743 in current penalties.
  • 9 deaths are linked to inspections that cited this rule.
  • Most citations: TX (11), MA (4), NE (4).
  • Related part: 1910.335(a) Use of protective equipment (290 citations).
  • Free 5-minute toolbox talk for your crew below.

Get the free 5-minute toolbox talk on 1910.335(a)(2)(i) ↓

48citations, 3 years
$248,743current penalties
48inspections
9linked deaths
In this article
  1. What this rule covers
  2. Official text
  3. Injuries linked to this rule
  4. Where and how often it was cited
  5. Free toolbox talk
  6. OSHA interpretation letters
  7. Related parts of this rule
  8. Get your crew competent
  9. Frequently asked questions
  10. About this page

What this rule covers

29 CFR 1910.335(a)(2)(i) is one requirement inside 1910.335 Safeguards for personnel protection, an OSHA general industry standard (Part 1910, Subpart S). It includes 2 sub-paragraphs. The official text below is copied word for word from the Electronic Code of Federal Regulations (eCFR). The numbers, injury cases and training on this page show how OSHA enforces it on real job sites.

Official text

(i) When working near exposed energized conductors or circuit parts, each employee shall use insulated tools or handling equipment if the tools or handling equipment might make contact with such conductors or parts. If the insulating capability of insulated tools or handling equipment is subject to damage, the insulating material shall be protected. 48 citations

(A) Fuse handling equipment, insulated for the circuit voltage, shall be used to remove or install fuses when the fuse terminals are energized. 4 citations

(B) Ropes and handlines used near exposed energized parts shall be nonconductive.

Source: eCFR, text current as of 2026-10-15. Read all of 1910.335.

See every company cited for this rule.

Export the list: 48 inspections cited 1910.335(a)(2)(i) in the last 3 years, with employer, location, penalty and date.

Purple Belt, $59/mo

Injuries linked to this rule

9 deaths are linked to inspections where OSHA cited 1910.335(a)(2)(i).

Two employees sustain burns contacting live wire, one dies
2024-11-20 · Fatal · TULSA, OK

At 12:21 p.m. on November 20, 2024, Employee #1 and Employee #2 were working as telecommunications repair installers for a telecommunications provider. The crewwas investigating a mystery wire that was uncovered by a homeowner in the back yard of a residence. The crew was tryin…

See all 9 cases

Full case list with employer, penalty, filters and download is part of OSHA Data (Purple Belt).

Unlock with Purple Belt

Where and how often it was cited

YearCitations
20232
202414
202515
202617

Top states: TX (11), MA (4), NE (4), OK (3), FL (3)

Largest penalties

EmployerLocationPenalty for this rule
GAGE TREE SERVICE LLCCHUGIAK, AK$99,308
EXACORE STAFFING LLCIRAAN, TX$19,863
KIRBY'S HEATING & AIR-CONDITIONING CO., INC.NORTH LITTLE ROCK, AR$16,550
SOUTH TEXAS ELECTRIC COOPERATIVE, INC.NURSERY, TX$16,131
COXCOM, LLCTULSA, OK$11,823

Free toolbox talk

A 5-minute crew talk on 1910.335(a)(2)(i), plus alerts when this rule changes. Free.




OSHA interpretation letters

None exist. OSHA has not published a letter of interpretation for 1910.335(a)(2)(i).

Related parts of this rule

Get your crew competent

Trainers on Black Belt Safety: Marc Harvey

Trainers and suppliers: feature your business on this rule for $25/month.

Frequently asked questions

When are insulated tools required?

When working near exposed energized conductors or circuit parts and the tools might contact them.

How must fuses be handled when terminals are energized?

With fuse handling equipment insulated for the circuit voltage.

What kind of ropes can be used near energized parts?

Only nonconductive ropes and handlines.

About this page

Sources

3-year window. Federal OSHA only; state-plan rules are not counted. Plain-language text is a summary, not legal advice; the official text controls. Black Belt Safety is not part of OSHA or the Department of Labor.

Written and reviewed by

Black Belt Safety Editorial Team

Site Safety Officer and Safety Professional

OSHA 30 · CPR · USACE CQM

Written and reviewed by the Black Belt Safety team. Every post is checked against the OSHA standard or agency source it cites.

Scroll to top