29 CFR 1910 · General Industry · Subpart O

1910.212(a): Machine guarding

By Black Belt Safety Editorial Team Official text as of October 15, 2026 Data updated November 17, 2026 4 min read

In plain words:

Machines must be guarded to protect the operator and everyone else in the machine area from hazards such as the point of operation, ingoing nip points, rotating parts, and flying chips and sparks. Guards should be attached to the machine where possible and must not create a hazard themselves. The point of operation must be guarded so no part of the body can be in the danger zone during the operating cycle; special hand tools can add protection but never replace a guard. Revolving drums, barrels and containers need interlocked enclosures, and fan blades less than 7 feet above the floor or working level must be guarded.

Key takeaways

  • 1910.212(a) is part of OSHA's general industry standards (29 CFR Part 1910, Subpart O).
  • OSHA cited it 6,843 times in the last 3 years, in 6,339 inspections, with $42,254,815 in current penalties.
  • 39 deaths are linked to inspections that cited this rule.
  • Most citations: OH (461), TX (434), WI (411).
  • Related part: 1910.212(a)(1) Types of guarding (4,631 citations).
  • Free 5-minute toolbox talk for your crew below.

Get the free 5-minute toolbox talk on 1910.212(a) ↓

6,843citations, 3 years
$42,254,815current penalties
6,339inspections
39linked deaths
In this article
  1. What this rule covers
  2. Official text
  3. Injuries linked to this rule
  4. Where and how often it was cited
  5. Free toolbox talk
  6. OSHA interpretation letters
  7. Related parts of this rule
  8. Get your crew competent
  9. Frequently asked questions
  10. About this page

What this rule covers

29 CFR 1910.212(a) ("Machine guarding") is one requirement inside 1910.212 General requirements for all machines, an OSHA general industry standard (Part 1910, Subpart O). It includes 9 sub-paragraphs. The official text below is copied word for word from the Electronic Code of Federal Regulations (eCFR). The numbers, injury cases and training on this page show how OSHA enforces it on real job sites.

Official text

(a) Machine guarding — 6,843 citations

(1) Types of guarding. One or more methods of machine guarding shall be provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks. Examples of guarding methods are—barrier guards, two-hand tripping devices, electronic safety devices, etc. Open (a)(1) 4,631 citations

(2) General requirements for machine guards. Guards shall be affixed to the machine where possible and secured elsewhere if for any reason attachment to the machine is not possible. The guard shall be such that it does not offer an accident hazard in itself. Open (a)(2) 217 citations

(3) Point of operation guarding. Open (a)(3) 1,833 citations

(i) Point of operation is the area on a machine where work is actually performed upon the material being processed. Open (a)(3)(i) 20 citations

(ii) The point of operation of machines whose operation exposes an employee to injury, shall be guarded. The guarding device shall be in conformity with any appropriate standards therefor, or, in the absence of applicable specific standards, shall be so designed and constructed as to prevent the operator from having any part of his body in the danger zone during the operating cycle. Open (a)(3)(ii) 1,648 citations

(iii) Special handtools for placing and removing material shall be such as to permit easy handling of material without the operator placing a hand in the danger zone. Such tools shall not be in lieu of other guarding required by this section, but can only be used to supplement protection provided. Open (a)(3)(iii) 115 citations

(iv) The following are some of the machines which usually require point of operation guarding: Open (a)(3)(iv) 40 citations

(a) Guillotine cutters.

(b) Shears.

(c) Alligator shears.

(d) Power presses.

(e) Milling machines.

(f) Power saws.

(g) Jointers.

(h) Portable power tools.

(i) Forming rolls and calenders.

(4) Barrels, containers, and drums. Revolving drums, barrels, and containers shall be guarded by an enclosure which is interlocked with the drive mechanism, so that the barrel, drum, or container cannot revolve unless the guard enclosure is in place. Open (a)(4) 28 citations

(5) Exposure of blades. When the periphery of the blades of a fan is less than seven (7) feet above the floor or working level, the blades shall be guarded. The guard shall have openings no larger than one-half (1⁄2) inch. Open (a)(5) 120 citations

Source: eCFR, text current as of 2026-10-15. Read all of 1910.212.

See every company cited for this rule.

Export the list: 6,339 inspections cited 1910.212(a) in the last 3 years, with employer, location, penalty and date.

Purple Belt, $59/mo

Injuries linked to this rule

39 deaths are linked to inspections where OSHA cited 1910.212(a).

Employee is fatally injured when struck by drill press arm
2025-03-04 · Fatal · MIAMI, FL

An employee was fabricating a part for an agricultural wagon using a drill presswhen it fell onto his head, causing multiple fatal injuries to the employee.

See all 39 cases

Full case list with employer, penalty, filters and download is part of OSHA Data (Purple Belt).

Unlock with Purple Belt

Where and how often it was cited

YearCitations
2023244
20242,492
20252,368
20261,739

Top states: OH (461), TX (434), WI (411), IL (408), PA (390)

Largest penalties

EmployerLocationPenalty for this rule
THE GOODYEAR TIRE & RUBBER COMPANYDANVILLE, VA$185,555
HUBBELL POWER SYSTEMS, INC.BOONTON TOWNSHIP, NJ$165,514
111367 - LINDAR CORPORATIONBAXTER, MN$165,514
VIRGINIA TRANSFORMER CORP.ROANOKE, VA$162,849
ATLAS TUBE (ALABAMA), INC.BIRMINGHAM, AL$161,323

Free toolbox talk

A 5-minute crew talk on 1910.212(a), plus alerts when this rule changes. Free.




OSHA interpretation letters

None exist. OSHA has not published a letter of interpretation for 1910.212(a).

Related parts of this rule

Get your crew competent

Trainers on Black Belt Safety: Marc Harvey

Trainers and suppliers: feature your business on this rule for $25/month.

Frequently asked questions

Can push sticks or hand tools replace a machine guard?

No. Special hand tools for placing and removing material may only supplement the guarding required by 1910.212. They cannot be used instead of it.

Which machines usually need point-of-operation guarding?

The standard lists guillotine cutters, shears, alligator shears, power presses, milling machines, power saws, jointers, portable power tools, and forming rolls and calenders.

When do fan blades need a guard?

When the edge of the blades is less than 7 feet above the floor or working level.

About this page

Sources

3-year window. Federal OSHA only; state-plan rules are not counted. Plain-language text is a summary, not legal advice; the official text controls. Black Belt Safety is not part of OSHA or the Department of Labor.

Written and reviewed by

Black Belt Safety Editorial Team

Site Safety Officer and Safety Professional

OSHA 30 · CPR · USACE CQM

Written and reviewed by the Black Belt Safety team. Every post is checked against the OSHA standard or agency source it cites.

Scroll to top